Dali H-60 Wartungshandbuch PDF herunterladen

Installation and Operating Instruction for B.E.G.-Occupancy detectors PD4-Master-TRIO-DALI-SM/-FC

A Light sensor 1 | B Light sensor 2

1 LED red OFF function

2 LED green too bright/too dark CDS 1

3 LED white semi-automatic DA 1/2

4 LED white semi-automatic DA 3

5 LED green too bright/too dark CDS 2

6 LED red motion indicator/walking test

2a.

Installation of the LUXOMAT

PD4-M-TRIO-DALI-SM

2b.

Installation of the

LUXOMAT

PD4-M-TRIO-DALI-FC

3. Hardware configuration

Position of light sensors and LEDs

LUXOMAT

PD4-M-TRIO-DALI

1. Mounting preparations

Work on the 230 V mains supply

may only be carried out by quali-

fied professionals or by instructed

persons under the direction and

supervision of qualified skilled elec-

trical personnel in accordance with

electrotechnical regulations.

Disconnect supply before installing!

When in Master/Slave mode of

operation, the Master-appliance

must always be installed at the

location where there is least

daylight.

Option:

Wall bracket for remote

control

IR-PD4-TRIO-DALI

A4 5 1 3 2 6

6. Putting into operation / Settings

Self test cycle

After an initial 60-second self-test cycle, the LUXOMAT

PD4-M-TRIO-DALI

is ready for operation.

Potentiometer 3: Follow-up time for light control

The time can be set infinitely variably at between

1 and 60 minutes. The time-setting is valid for all three chan-

nels of the PD4-M-TRIO-DALI.

Symbol TEST: Test mode (Every movement switches on the

light for a period of 2 second, switching it off for a period of

2 seconds after that regardless of the level of brightness.)

Potentiometer 2: Twilight-switch for light control

The switch-on value for the light can be set at between 40

and 1200 Lux. Using the rotary control, the luminance set

points can be set as desired.

Symbol

: Night-time operation

Symbol

: Daytime/Night-time operation

Potentiometer 1: Orientation lighting

This rotary controller serves to determine the working time of

the orientation lighting (fixed to 20 %).

“ON” for permanent orientation lighting.

“OFF” for deactiviation of orientation lighting.

TEST

1200

600

200

OFF

80 - 90 mm

100 mm

DA 1/2 ON/OFF

max

Lux

1500

Lux

OFF

Settings by remote control









min

Fully /semi automatic mode

(only

DA 1/2

)

=> see page 2, point 7

LED display ON/OFF

Resetting when

open: All values

which have been

programmed

using the remote

control are de-

leted, and those

values which

have been set by

potentiometer are

activated.

Dimming (=> see page 2, point 8)

The following approach will prove useful when setting a command

value (example workplace): Place a luxmeter flat on the desk,

then, using the remote control IR-PD4-TRIO-DALI, adjust the light up

or down by pressing the keys max or min until the desired com-

mand value which best suits your requirements has been reached.

Saving of the through adjusted luminance set point

100 h function

to extend the life span – sums up automatically the burning time

of 100 % luminosity at the beginning up to 100 hours – only

then can lights dim

Activate test mode - when locked

Deactivate test mode: press Reset

Resetting when locked

The lighting relay is switched off, i.e. opened and the follow-up

times reset.

Permanent protection against sabotage when locked

This function blocks the unit permanently (all LEDs are flashing).

All functions of the remote control are locked. Proceed to exit this

mode: reset the hardware using DIP switch 3 or switch the supply

voltage as follows:

DA 1/2 ON/OFF when locked (=> see page 2, point 9)

The light will remain switched on/off for as long as movements

are detected in the areas of coverage. Once the last movement

has been detected, the light will remain on for the duration of

the follow-up time as per setting.

The appliance will then return independently to the mode

selected (Fully or Semi-automatic).

Orientation lighting and its follow-up time ON/OFF

Note: During the orientation light phase, the constant light

regulation is also active: if there is sufficient brightness, dimming

occurs < 2V and, if applicable, the lighting is switched off.

Orientation lighting – Adjustment ot the light intensity

The orientation lighting is adjustable in a span from 10 to 30 %

of the nominal light. Standard adjustment is 20 %.

Explanation of the key functions

1000

100

DIP 1 HA / A

DIP 2 Ini OFF/ON

Lamps at start-up OFF/ON

DIP 3 RESET

5. Position of potentiometer and DIP switch

DIP

123

DIP

321

1 2 3

230V

1sec. 1sec.30 sec. - 60 sec.

OFF

The detector must be in stalled on a solid and

level surface. The circular cover ring must be

removed prior to assembly. To do this, twist the

lens (C) anticlockwise through approximately 5°

and lift off.

Having connected up the wires in accordance with

regulations, secure the detector with 2 screws.

After installation replace the lens and lock (turn

clockwise). Mains to be connected

open

A circular opening

of diameter 100 mm

must be produced in

the ceiling.

Having connected

up the cables in

accor dance with

regulations, the

detector is inserted

into the opening as

shown and fixed

into position with

the retaining bracket

using screws.

4. Putting into operation of the

remote control (optional)

Remote control

LUXOMAT

IR-PD4-TRIO-DALI

1. Check Battery:

open battery compartment by pressing

the plastic springs together and remo-

ving the battery-holder.

Caution:

Settings with remote control supersede

the settings by courtesy of potentio-

meters.

Unlocking device

Dimming of the luminance set

point (only for channel 1 and 2)

Luminance set point for

constant light regulation

Sun button – preselected light value

(Daylight operation)

Follow-up time light

100 h function

Orientation lighting and its

follow-up time ON/OFF

Orientation lighting

follow-up time

Orientation lighting

10 – 30% of nominal light

Saving of the dimmed

luminance set point

SM FC

t < 5 sec.

max

Lux

1500

Lux

OFF

Locking device – Exit

programming mode

Permanent protection against

sabotage

LED ashes

1 2

PD4-M-TRIO-DALI 1

Inhaltsverzeichnis

Seite 1 - PD4-M-TRIO-DALI

Installation and Operating Instruction for B.E.G.-Occupancy detectors PD4-Master-TRIO-DALI-SM/-FCA Light sensor 1 | B Light sensor 21 LED red

Seite 2

15. Technical data PD4-M-TRIO-DALI Sensor and power supply in one casePower supply: 230V~ ±10%Power consumption: < 1WAmbient temperature: -25

Weitere Dokumente für Soundbar-Lautsprecher Dali H-60

Um das Dokument anzuzeigen Dali H-60 Bedienungsanleitung

Dali H-60 Bedienungsanleitung (6 Seiten)

Dali H-60 Bedienungsanleitung (8 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Dali H-60 Wartungshandbuch

Stöbern Sie online oder laden Sie Wartungshandbuch nach Soundbar-Lautsprecher Dali H-60 herunter. Dali H-60 Technical data Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Soundbar-Lautsprecher Dali H-60

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Soundbar-Lautsprecher Dali H-60